Impulse 7205e Uživatelský manuál

COMM+2.LPCIe User Manual Item Numbers 7205e & 7205eS www.sealevel.com PO Box 830 – Liberty, SC 29657 864.843.4343

Software Installation, continued 13. The setup file will automatically detect the operating environment and install the proper components. When the ‘

Hardware Installation Do not install the PCI Express board until the software has been successfully installed. The 7205e is shipped configured fo

Hardware Installation, continued 5. Choose ‘Install the software automatically’ and click ‘Next’. 6. The ‘Hardware Wizard’ will search for the

Hardware Installation, continued 7. The appropriate drivers for your SeaLINK device and version of Windows will be installed as shown. 8. Click

10. When the ‘Found New Hardware’ alert informs you that your hardware is installed and ready to use, you can proceed with verifying the installation

Verifying Installation To confirm that the serial port has been successfully installed, look in Device Manager under ‘Ports (COM &LPT)’ and the C

Uninstall & Upgrade Instructions The SeaCOM software program adds entries to the system registry that are necessary for specifying the operating

Remove Hardware, continued 6. Right click on the entry for the ‘ULTRA COMM+2.LPCIe’ device and click ‘Uninstall’ in the fly out menu. 7. Confir

Remove Software Using Control Panel Make sure you have first removed the hardware using the instructions on the previous page before removing the sof

Upgrade Instructions With the device still installed in a PCI Express slot, install the latest version of SeaCOM. You can download the latest version

Table of Contents INTRODUCTION...

Hardware Description PCI Express Board The 7205e is a low profile PCI Express 1.0a compliant board via single-lane x1 slot. It can be used in any

Electrical Specifications Each serial port utilizes a 16C950 UART featuring programmable baud rates, data format, interrupt control and industry-lead

Cable Pin Assignments The 7205e includes a cable (Item# CA203) with a DB25 female connector terminating to a pair of DB9 male connectors. The DB25F c

Baud Rates and Oscillator Value The 7205e utilizes a 14.7456MHz oscillator, which is automatically entered by the SeaCOM driver under Windows 2000/XP

Technical Specifications Dimensions Length Width 5.75” 2.54” 14.60 cm 6.45 cm Environmental Specifications Specification Operating Storage Tempe

Appendix A – Troubleshooting The adapter should provide years of trouble-free service. However, in the event that it appears to be functioning incorr

 On the ‘Port Information’ tab, select the COM port you want to test and click on the ‘Open’ button. (See image below)  Click the ‘Settings’ bu

 Click on the ‘Start’ button. If testing RS-485, be sure that ECHO is enabled. (See image below)  If the COM port is working properly, the gre

Appendix B – How To Get Assistance Begin by reading the Troubleshooting Guide (Appendix A). This will help solve most common problems. 1. When calli

Appendix C – Electrical Interface RS-232 Quite possibly the most widely used communication standard is RS-232. This implementation has been defined

Introduction The Sealevel COMM+2.LPCIe (Item# 7205e) provides a PCI Express 1.0a compliant interface adapter with two asynchronous serial ports for i

Appendix D – Asynchronous Communications Serial data communications implies that individual bits of a character are transmitted consecutively to a re

Appendix E – Mechanical Drawing © Sealevel Systems, Inc. - 29 - COMM+2.LPCIe User Manual

Appendix F – Compliance Notices Federal Communications Commission Statement This equipment has been tested and found to comply with the limits for Cl

© Sealevel Systems, Inc. - 31 - COMM+2.LPCIe User Manual Warranty Sealevel's commitment to providing the best I/O solutions is reflected in the

Before You Get Started What’s Included Depending on the PC bracket ordered, the 7205e is shipped with the following items. If any of these items are

Hardware Configuration There are two sets of 7-position dipswitches on the board that are used to set the electrical interface, termination and biasi

Electrical Interface Modes Each port on the 7205e can be individually configured for RS-232, RS-422, or RS-485 mode. The first two switches labeled ‘

Installation & Configuration Software Installation Windows 98/ME/2000/XP/Vista™ Operating Systems Do not install the PCI Express board until th

Software Installation, continued 8. When the ‘License Agreement’ window appears, accept the terms and click ‘Next’ to continue. You can click the ‘P

Software Installation, continued 10. A dialog box will appear, as shown, with important information. Click the ‘OK’ button to continue. 11. During